Microtensile bond strength of resin cements to 3-D printed and milled temporary restorative resins / Resistencia de unión en microtracción de cementos resinosos a resinas para provisionales impresas y fresadas

Abstract To evaluate the microtensile bond strength (µTBS) of two resin cements to 3D printed and milled CAD/CAM resins used for provisional fixed partial dentures. Blocks (5 x 5 x 5 mm) of three 3D-printed resins (Cosmos3DTemp / Yller; Resilab3D Temp / Wilcos and SmartPrint BioTemp, / MMTech) were printed (Photon, Anycubic Technology Co.). A milled material (VitaCAD-Temp, VITA) was used as control. Half the specimens were sandblasted and the rest were untreated. Two blocks were bonded with the corresponding resin cement: PanaviaV5 (Kuraray Noritake) and RelyX Ultimate (3M Oral Care). After 24 hours, the bonded blocks were sectioned into 1 x 1 mm side sticks. Half the beams were tested for µTBS and the other half was thermocycled (5000 cycles, 30s dwell-time, 5s transfer time) before µTBS testing. A four way Generalized Linear Model (material*sandblasting*cement*aging) analysis was applied. VITA exhibited the lowest µTBS, regardless of the cement, sandblasting and thermocycling. Sandblasting significantly improved the µTBS of VIT, especially after aging, but did not improve the µTBS of 3D printed resins. Sandblasting was not beneficial for 3D printed resins, although is crucial for adhesive cementation of milled temporary resins. Airborne particle abrasion affects the integrity of 3D-printed resins, without producing a benefit on the microtensile bond strength of these materials. However, sandblasting is crucial to achieve a high bond strength on milled temporary resins.

Resumen Evaluar la resistencia adhesiva en microtracción (µTBS) de dos cementos resinosos a resinas CAD/CAM impresas y fresadas indicadas para restauraciones provisionales. Bloques (5 x 5 x 5mm) de tres resinas impresas (Cosmos3DTemp / Yller; Resilab3D Temp / Wilcos and SmartPrint BioTemp, / MMTech) y una resina fresada (VitaCAD-Temp, VITA) fueron fabricados. La mitad de los especímenes fueron arenados y el resto no recibió tratamiento mecánico. Dos bloques con condiciones de tratamiento iguales fueron cementados con cemento resinoso (PanaviaV5 / Kuraray Noritake y RelyX Ultimate / 3M Oral Care). Después de 24 horas los bloques fueron seccionados en palitos de 1 mm² de área. En la mitad de los especímenes se midió la TBS inmediatamente y el resto fue termociclado (5000 ciclos, 30s remojo, 5s transferencia) antes de la prueba de TBS. Se aplica un análisis estadístico por Modelo Linear General con 4 factores (material*arenado*cemento*termociclado). La resina VITA presentó la menor µTBS, independientemente del cemento usado, el arenado y el termociclado. Sin embargo, el arenado aumentó la µTBS de VIT, especialmente después del termociclado. Por otro lado, el arenado no resultó en un aumento significativo de la µTBS de las resinas impresas. El arenado no fue beneficiosos para las resinas impresas, aunque es un paso crucial para la cementación adhesive de las resinas fresadas. El arenado afecta la integridad de las capas de las resinas impresas, sin generar un beneficio en la TBS.

Resina Filtek Z250 XT precalentada como agente cementante de restauraciones indirectas / Preheated Filtek Z250 XT resin as a luting agent in indirect restorations

Introducción: Las restauraciones indirectas de resina son ampliamente empleadas para realizar tratamientos estéticos en dientes posteriores. Recientemente se ha propuesto el uso de resinas precalentadas como agentes de unión. Objetivo: Evaluar la resistencia a la tracción de restauraciones indirectas cementadas con una resina precalentada comparándola con un cemento de resina autoadhesivo y un cemento resinoso. Métodos: Las preparaciones dentarias se realizaron en 45 premolares con piedras diamantadas calibradas. Las muestras se dividieron aleatoriamente en tres conjuntos (n = 15) según los grupos experimentales: grupo 1 (resina precalentada), grupo 2 (resina autoadhesiva) y grupo 3 (cemento de resinoso adhesivo). Las muestras fueron incluidas en acrílico autopolimerizable. Se realizaron restauraciones indirectas para cada muestra, las superficies internas fueron microarenadas y se aplicó silano antes de la cementación con los agentes de unión. La resistencia a la tracción se realizó utilizando una máquina universal de ensayos con una velocidad de cruceta de 5 mm/min. El análisis estadístico se llevó a cabo con ANOVA de un factor y la prueba post hoc de Tukey. Se adoptó un nivel de significancia de p < 0,05. Resultados: La resina Filtek Z250 XT precalentada a 60 °C durante 15 minutos tuvo una fuerza de resistencia a la tracción de 5,775 MPa, similar a RelyX Ultimate con 5,442 MPa (p > 0,05), ambos grupos poseen una fuerza de resistencia a la tracción significativamente mayor que RelyX U200 (3,430 MPa). Conclusiones: La resina precalentada (Filtek, Z250 XT) y el cemento resinoso (RelyX Ultimate) muestran las mismas propiedades de resistencia a la tracción cuando se usan como agentes adhesivos en restauraciones indirectas de resina(AU)

Introduction: Indirect resin restorations are widely used in the esthetic treatment of posterior teeth. Preheated resins have been recently proposed as luting agents. Objective: Evaluate the tensile bond strength of indirect restorations cemented with a preheated resin versus a self-adhesive resin cement and a resinous cement. Methods: Tooth preparation was conducted of 45 premolars using calibrated diamond-coated stones. The samples were randomly divided into three sets (n = 15) according to the following experimental groups: Group 1 (preheated resin), Group 2 (self-adhesive resin) and Group 3 (adhesive resinous cement), and soaked in self-polimerizable acrylic. Indirect restorations were performed for each sample. The inner surfaces were microsanded, and silane was applied before cementation with the luting agents. Tensile bond strength was verified with a universal testing machine at a crosshead speed of 5 mm/min. Statistical analysis was based on one-factor ANOVA and Tukey's post hoc test. A significance level of p < 0.05 was established. Results: The Filtek Z250 XT resin preheated at 60°C for 15 minutes displayed a tensile bond strength of 5.775 MPa, similar to RelyX Ultimate with 5.442 MPa (p > 0.05). Both groups displayed a significantly greater tensile bond strength than RelyX U200 (3.430 MPa). Conclusions: The preheated resin (Filtek Z250 XT) and the resinous cement (RelyX Ultimate) exhibit the same tensile bond strength properties when used as luting agents in indirect resin restorations(AU)

Microtensile Bond Strength Between Self-Adhesive Resin Cements and Resin Based Ceramic CAD/CAM Block / Resistencia adhesiva microtensil entre cementos de resina autoadhesivos y bloques de cerámica CAD/CAM a base de resina

Abstract: Purpose: The objective of this study is to evaluate and compare the microtensile bond strength (μTBS) of four different self-adhesive resin cements to a resin-based ceramic CAD/CAM block, at the baseline, and after subjecting them to 5,000 thermo-cycles.Materials and Methods: Four self-adhesive dual-cured resin cements; G-CEM LinkAce (GC EUROPE, Leuven, Belgium), RelyX U200 (3M ESPE, Seefeld, Germany), Maxcem Elite (Kerr, CA, USA), TheraCem (Bisco, Schaumburg, USA) were applied to Cerasmart CAD/CAM blocks (GC EUROPE, Leuven, Belgium). CAD/CAM blocks were sectioned into sticks and subjected to µTBS tests at 24 hours, and the other half were subjected to tests after 5000 thermo-cycles. The data were tested by one-way variance analysis (p<0.05). Results: The highest bond strength values were observed in TheraCem, followed by G-CEM LinkAce and RelyX U200, respectively (p<0.05). At the baseline, G-CEM LinkAce, RelyX U200, and Maxcem Elite showed statistically similar results. After 5,000 thermal-cycles, a significant decrease was observed in the bond strength values of G-CEM LinkAce (p<0.05). Conclusion: Between the adhesive cements used in the study, TheraCem showed the highest micro-tensile bond strength values both in the baseline (24h) results, and after the 5,000 thermal- cycle aging procedures.

Resumen: Propósito: Evaluar y comparar la resistencia adhesiva microtensil (μTBS) de cuatro cementos de resina autoadhesivos diferentes con un bloque CAD/CAM de cerámica a base de resina, antes y después de 5.000 ciclos de termociclado. Materiales y métodos: cuatro cementos de resina de doble curado autoadhesivos; G-CEM LinkAce (GC EUROPE, Lovaina, Bélgica), RelyX U200 (3M ESPE, Seefeld, Alemania), Maxcem Elite (Kerr, CA, EE. UU.), TheraCem (Bisco, Schaumburg, EE. UU.) fueron aplicados a bloques Cerasmart CAD/CAM (GC EUROPE, Lovaina, Bélgica). Los bloques CAD/CAM se seccionaron en barras y se sometieron a pruebas µTBS a las 24 horas, y la otra mitad se sometió a pruebas después de 5000 ciclos térmicos. Los datos fueron probados por análisis de varianza unidireccional (p<0.05). Resultados: Los valores más altos de fuerza de unión se observaron en TheraCem, seguido de G-CEM LinkAce y RelyX U200, respectivamente (p<0.05). En la línea de base, G-CEM LinkAce, RelyX U200, Maxcem Elite mostró resultados estadísticamente similares. Después de 5.000 procesos de ciclo térmico, se observó una disminución significativa en los valores de resistencia de la unión de G-CEM LinkAce (p<0.05). Conclusión: entre los cementos adhesivos utilizados en el estudio, TheraCem mostró los valores más altos de resistencia de la unión micro-extensible tanto en la línea de base (24 h) como después de 5,000 procedimientos de envejecimiento térmico.

Comparación in vitro del espesor y homogeneidad de la capa de cementación en carillas indirectas, realizado con resina fluida vs cemento de resina fotodependiente / Comparison of thickness and homogeneity of thecementationlayer in indirectveneers, madewith fluidresin vs. light-cure resincement: in vitro study

Resumen Objetivo: Comparar el grosor y homogeneidad de la capa de cementación entre un cemento de resina fotodependiente y una resina fluida. Materiales y métodos: Para la obtención de la muestra se talló la preparación en un diente de marfilina, el cual fue escaneado y luego replicado 92 veces en un polímero ABS. La muestra se dividió en 2 grupos con 46 muestras cada uno. Se realizó la cementación de las carillas con resina fluida Tetric N-Flow en el grupo G1, y con cemento de resina fotodependiente VariolinkEsthetic en el grupo G2. Cada muestra fue previamente lavada con alcohol de 70°, luego secada y se aplicó una capa de adhesivo TetricN-Bond. Se utilizó presión digital para lograr el asentamiento final de las carillas. Finalmente se realizó un corte medial y uno paramedial para obtener muestras de 2 mm aproximadamente, las cuales se observaron y midieron en un microscopio óptico. Resultados: El promedio de grosor para Tetric N-Flow fue de 119μm en incisal, 113μm en medio y 107μm en cervical. Para VariolinkEsthetic el promedio fue de 117μm, 112μm y 110μm en incisal, medio y cervical respectivamente. La homogeneidad fue de un 93,3% para G1 y 91,3% para G2. Conclusión: No existe diferencia significativa en el grosor y homogeneidad de la capa de cementación realizado con resina fluida y con cemento de resina fotodependiente.

Abstract Objective: Compare the thickness and homogeneity of the cementing layer between a light-cure resin cementand a flowable resin. Materials and methods: To obtain the sample, the preparation was carved in a replica of tooth 1.1 (EWL modelteeth, Kavo), which was scanned and then replicated 92 times in an ABS polymerby 3D printing. The simple was divided into 2 groupswith 46 sample seach. The cementation of the veneres was performed with Tetric N-Flow flowable resin in the G1 group, and with Variolink Esthetic light-cure resin cement in the G2 group. Each simple was previously washed with 70° alcohol, then dried and a layer of Tetric N-Bond was applied. Digital pressure was used to achieve the final settlement of the veneers. Finally, a medial and a paramedial section were made to obtain approximately 2 mm thick samples. The cementation layer was observed with an optical microscope. Results: The average thickness for Tetric N-Flowwas 119μm in incisal, 113μm in medium and 107μm in cervical. For Variolink Esthetic the average was 117μm, 112μm and 110μm in incisal, middle and cervical respectively. The homogeneity was 93.3% for G1 and 91.3% for G2. Conclusion: There is no significant difference in the thickness and homogeneity of the cementing layer made with flowable resin and with light-cure resincement.

Bonding of universal adhesive system to enamel surrounding real-life carious cavities

Abstract: This study aimed to evaluate the bond strength of a universal adhesive system to enamel surrounding real-life carious cavities. Twenty-eight permanent molars (n = 7) with carious lesions in dentin were subjected to selective carious tissue removal to firm dentin and had their crowns sectioned longitudinally. A universal adhesive system (Single Bond Universal [SBU] used in either etch-and-rinse and self-etch strategies) was compared with an etch-and-rinse Adper Single Bond 2 (ASB) and a self-etch Clearfil SE Bond (CSE) adhesive systems (control systems). Adhesives were applied on the enamel, assumed demineralized, surrounding the cavity margins and on sound enamel (control substrate). Composite cylinders were built (0.72 mm2) and microshear bond strength (µSBS) test was performed after 24 h of water storage. The µSBS values (MPa) were analyzed using two-way ANOVA and Tukey's post hoc tests (α = 0.05). Bond strength values obtained in demineralized enamel surrounding carious cavity margins were significantly lower than that obtained in sound enamel (distant from carious cavity margins) (p = 0.035). The bonding strategy of the SBU did not influenced the bond strength values, which were higher than that obtained with ASB. CSE showed similar µSBS values to ASB and SBU in the self-etch mode. In conclusion, the bond strength to enamel assumed demineralized is lower than to sound enamel. The enamel surrounding carious cavities jeopardize the bonding of universal adhesive system. The bond strength of universal adhesive is similar, regardless to bonding strategy.

Longevity of metal-ceramic crowns cemented with self-adhesive resin cement: a prospective clinical study

Abstract Resin cements are often used for single crown cementation due to their physical properties. Self-adhesive resin cements gained widespread due to their simplified technique compared to regular resin cement. However, there is lacking clinical evidence about the long-term behavior of this material. The aim of this prospective clinical trial was to assess the survival rates of metal-ceramic crowns cemented with self-adhesive resin cement up to six years. One hundred and twenty-nine subjects received 152 metal-ceramic crowns. The cementation procedures were standardized and performed by previously trained operators. The crowns were assessed as to primary outcome (debonding) and FDI criteria. Statistical analysis was performed using Kaplan-Meier statistics and descriptive analysis. Three failures occurred (debonding), resulting in a 97.6% survival rate. FDI criteria assessment resulted in scores 1 and 2 (acceptable clinical evaluation) for all surviving crowns. The use of self-adhesive resin cement is a feasible alternative for metal-ceramic crowns cementation, achieving high and adequate survival rates.

Cierre de diastema central maxilar por terapia cosmética convencional con resina nanoparticulada / Central closure jaw diastema conventional cosmetic therapy nanoparticulate resin

Son muchos los factores que influyen en el éxito del tratamiento cosmético para el cierre del diastema central, debido a las múltiples causas que provocan la presencia de esta entidad. Dentro de ellas, la avulsión traumática de uno de los incisivos centrales constituye una de las principales y más complejas problemáticas a solucionar. El propósito es describir un caso de cierre de diastema central maxilar para el restablecimiento de la estética de un paciente, con el uso de resina nanoparticulada como material restaurador. Como parte del tratamiento a un paciente masculino de 25 años de edad, con retraso mental ligero y antecedente de traumatismo dentario con avulsión del incisivo central superior derecho 1.1., se realizó el cierre de diastema central superior con la aplicación de resina nanoparticulada, previa preparación biomecánica y grabado ácido. La técnica utilizada constituye una alternativa terapéutica que beneficia notablemente al paciente. Con la secuencia de los pasos propuestos, que ofrece numerosas ventajas en comparación a la presentada por otros autores en casos similares, se restablece en una sola visita la estética del paciente, mediante un adecuado diagnóstico clínico y planificación rigurosa del tratamiento(AU)

There are many factors that influence the success of cosmetic treatment for the closure of a central diastema, because of the multiple causes to the presence of this entity. Among them, the traumatic avulsion of one of the central incisors is one of the largest and most complex problems to be solved. The objective is to describe a case of closure of a central maxillar diastema to restore the aesthetic appearance of a patient, using resin as a restorer nano-particle material. As part of the treatment to a male 25-year-old patient with mild mental retardation and history of dental injury with avulsion of the right 1.1 maxillary central incisor, the closure of the upper central diastema was performed with the application of nano-particle resin, prior to preparation of biomechanics and acid application. The technique used constitute is a therapeutic alternative that greatly benefits the patient. With the sequence of the proposed steps, which offers numerous advantages compared to that presented by other authors in similar cases, the aesthetic appearance of the patient was reestablished after just one visit by the appropriate clinical diagnosis and thorough a planned treatment(AU)

Evaluación In vitro de la Resistencia a la Fractura de los Pilares Individualizados en Disilicato de Litio / In vitro Evaluation of the Fracture Strength of Lithium Disilicate Custom Abutments

Los pilares híbridos individualizados en disilicato de litio, permiten adaptarse a la forma y el perfil de emergencia obtenido después de la temporalización de los implantes, presentando buenas características ópticas y determinando la posibilidad de una cementación adhesiva. El propósito del estudio fue evaluar la resistencia a la fractura de pilares individualizados en disilicato de litio en comparación con los pilares en circona-ytria tetragonal (Y-TZP), ambos cementados en una base de titanio PGTB (Ti base) mediante un estudio experimental in vitro. Se confeccionaron 10 pilares: 5 como grupo control, elaborados en Y-TZP, mediante el sistema Ceramill multi­X Amanngirrbach® y 5 pilares híbridos en disilicato de litio mediante la técnica de inyección (IPS e.max® press abutment solution, Ivoclar Vivadent) como grupo experimental. Cada pilar se precargó a un implante con un torque de 30 N/cm2. Todas las coronas se fabricaron en disilicato de litio (técnica monolítica) y se cementaron usando cemento resinoso de curado dual (RelyX® U200, 3M ESPE). La medición de la resistencia a la fractura se realizó en una maquina universal de pruebas (instron®), modelo 2519-105. La resistencia a la fractura fue almacenada y evaluada utilizando la prueba paramétrica t-student. Para evaluar las fracturas incipientes y clasificar el tipo de falla se usó un microscopio óptico Carl Zeiss. los valores de resistencia promedio para los pilares de disilicato de litio fueron de 655,5 N y para los de circona 780,52 N con una desviación estándar de 145,76 N y 147,71 N, respectivamente. Ambos tipos de pilares evidenciaron buen comportamiento ante la prueba de resistencia a la fractura; sin embargo, se requieren más estudios que evalúen este tipo de pilares.

Hybrid lithium disilicate custom abutments are devices that adjust the shape and the emergency profile of the implant supported restorations in each clinical situation, getting good optical characteristics and the possibility of adhesive cementation. The purpose of the study was to compare the fracture strength of Ti-base Hybrid lithium disilicate and yttria-tetragonal zirconia custom abutments through an experimental in vitro study. Ten abutments were prepared, five as a control group made in Y-TZP by multi-system X Ceramill Amann Girrbach®, and five lithium disilicate hybrid abutments by heat press technique (IPS e.max® press abutment solution, Ivoclar Vivadent) as experimental group. Each abutment was preloaded to an implant with torque of 30 N/cm2. The crowns were fabricated in lithium disilicate (monolithic technique) and cemented using dual-curing resin cement, RelyX U200, 3M ESPE. The fracture strength measurements were performed on a universal testing machine (instron®), stored and evaluated using the t-student parametric test. An optical microscope (Carl Zeiss) was used to evaluate the incipient fractures and classify the type of failure. The average fracture strength of Ti-base Hybrid lithium disilicate was 655.5 N and the value for yttria-tetragonal zirconia custom abutments was 780.52 N, with a standard deviation of 145.76 N and 147.71 N, respectively. In both cases there was no statistical difference. Both types of abutments showed good performance to fracture strength test. Nevertheless more studies are required to evaluate this type of abutments.

Influência do agente cimentante e desajuste interno na adaptação marginal de coroas em resina nanocerâmica / Influence of the cement agent and internal mismatch in the marginal adaptation of nanoceramic resins crowns

A adaptação marginal é um dos requisitos fundamentais para a longevidade e o sucesso das restaurações. O objetivo desse estudo foi avaliar a influência do desajuste interno associado à diferentes agentes cimentantes na desadaptação marginal de coroas em resina nanocerâmica (Lava Ultimate 3M ESPE) confeccionadas pelo sistema CAD-CAM. A partir do escaneamento de um preparo de coroa total em um pré-molar, foram obtidos 36 modelos em metal. Esses foram divididos em seis grupos de acordo com o desajuste interno (70 µm ou 100 µm) e o cimento (Fosfato de zinco- SS White, Cimento de ionômero de vidro- Ketac Cem 3M/ESPE e Cimento resinoso- Relyx Ultimate 3M/ESPE). Após escaneamento de todos os modelos as coroas foram confeccionadas a partir da fresagem de blocos de resina nanocerâmica (Lava Ultimate 3M/ESPE). Com auxílio de microscópio óptico comparador (40X) foram medidas as desadaptações marginais prévia e posteriormente à cimentação, sendo considerados 8 pontos ao longo do término em todas as faces do corpo de prova. Os valores obtidos após serem submetidos aos testes two-way anova e teste t, demonstraram que as coroas confeccionadas com desajuste interno de 70 µm apresentam desadaptação marginal inferior estatisticamente significante às coroas com desajuste interno de 100 µm. Para o desajuste interno de 70 µm o grupo do cimento fosfato de zinco apresentou o menor gap marginal, sendo que este valor não foi estatisticamente diferente em relação ao grupo do Ketac Cem. Ainda com esse desajuste, o grupo do Ketac Cem não apresentou diferença estatística significante em relação ao grupo do Relyx Ultimate, no entanto esse último promoveu "gap" marginal estatisticamente maior em relação ao grupo do cimento fosfato de zinco. Para o desajuste interno de 100 µm não houve diferença estatisticamente significante no "gap" marginal entre os três cimentos avaliados. O presente estudo demonstrou através da metodologia utilizada, que a menor desadaptação marginal observada nas restaurações de Lava Ultimate, foi proveniente do desajuste interno de 70 µm. Neste grupo os cimentos de fosfato de zinco e de ionômero de vidro demonstraram melhor comportamento comparado ao cimento resinoso, embora o cimento de ionômero de vidro numericamente, mas não estatisticamente tenha apresentado resultado inferior ao do fosfato de zinco

The marginal adaptation is one of the basic requirements for the longevity and success of restorations. The aim of this study was to evaluate the influence of the internal imbalances associated with different luting agents on marginal leakage of crowns Nanoceramic resin ( Lava Ultimate 3M ESPE) made by CAD-CAM system. From the scanning of a full crown preparation in a pre molar were obtained 36 metal models. These were divided into six groups according to the internal imbalances ( 70 or 100 micrometres) and cement (SS White Zinc phosphate, glass ionomer cemet Ketac Cem 3M/ Espe and resinous cement Relyx Ultimate 3M / Espe). After scanning all models crowns were made from milling Nanoceramic resin blocks (Lava Ultimate 3M / Espe). With the aid of optical comparator microscope (40X) were measured prior marginal mismatches and after the cementation, being considered 8 points along the end in all specimen faces. The values were submitted to ANOVA two-way test and t test. Results showded that crowns made with internal imbalances of 70 uM show statistically significant lower marginal leakage to the crows with internal imbalances of 100 micrometres. For the internal imbalances 70 uM zinc phosphate cement group showed the lowest "gap" marginal, and this figure does not show a statistically significant difference compared to Ketac Cem gropu. Even with this misfit, Ketac Cem group showed no statistically significant difference in relation to Relyx Ultimate group, though the latter showed a statistically significant difference compared to zinc phosphate cement group. For the internal imbalances of 100 micrometres there was no statistically significant difference in the "gap" marginal among the three cements. This study demostrated through the methodology used, the lower marginal leakage oberved in Lava Ultimate restorations, was from the inner misfit 70 micrometers...

Marginal integrity of restorations produced with a model composite based on polyhedral oligomeric silsesquioxane (POSS)

Marginal integrity is one of the most crucial aspects involved in the clinical longevity of resin composite restorations.Objective To analyze the marginal integrity of restorations produced with a model composite based on polyhedral oligomeric silsesquioxane (POSS).Material and Methods A base composite (B) was produced with an organic matrix with UDMA/TEGDMA and 70 wt.% of barium borosilicate glass particles. To produce the model composite, 25 wt.% of UDMA were replaced by POSS (P25). The composites P90 and TPH3 (TP3) were used as positive and negative controls, respectively. Marginal integrity (%MI) was analyzed in bonded class I cavities. The volumetric polymerization shrinkage (%VS) and the polymerization shrinkage stress (Pss - MPa) were also evaluated.Results The values for %MI were as follows: P90 (100%) = TP3 (98.3%) = B (96.9%) > P25 (93.2%), (p<0.05). The %VS ranged from 1.4% (P90) to 4.9% (P25), while Pss ranged from 2.3 MPa (P90) to 3.9 MPa (B). For both properties, the composite P25 presented the worst results (4.9% and 3.6 MPa). Linear regression analysis showed a strong positive correlation between %VS and Pss (r=0.97), whereas the correlation between Pss and %MI was found to be moderate (r=0.76).Conclusions The addition of 25 wt.% of POSS in methacrylate organic matrix did not improve the marginal integrity of class I restorations. Filtek P90 showed lower polymerization shrinkage and shrinkage stress when compared to the experimental and commercial methacrylate composite.

The modified Ottawa method to establish the update need of a systematic review: glass-ionomer versus resin sealants for caries prevention

OBJECTIVE: To demonstrate the application of the modified Ottawa method by establishing the update need of a systematic review with focus on the caries preventive effect of GIC versus resin pit and fissure sealants; to answer the question as to whether the existing conclusions of this systematic review are still current; to establish whether a new update of this systematic review was needed. METHODS: Application of the Modified Ottawa method. Application date: April/May 2012. RESULTS: Four signals aligned with the criteria of the modified Ottawa method were identified. The content of these signals suggest that higher precision of the current systematic review results might be achieved if an update of the current review were conducted at this point in time. However, these signals further indicate that such systematic review update, despite its higher precision, would only confirm the existing review conclusion that no statistically significant difference exists in the caries-preventive effect of GIC and resin-based fissure sealants. CONCLUSION: In conclusion, this study demonstrated the modified Ottawa method as an effective tool in establishing the update need of the systematic review. In addition, it was established that the conclusions of the systematic review in relation to the caries preventive effect of GIC versus resin based fissure sealants are still current, and that no update of this systematic review was warranted at date of application. .

Intra-radicular dentin treatments and retention of fiber posts with self-adhesive resin cements

The aim of this study was to evaluate the effect of treating intraradicular dentin with irrigating solutions on the retention of glass-fiber posts luted with self-adhesive resin cement. Bovine incisors were endodontically treated, and 9-mm-deep postholes were prepared. Before inserting the cement, the root canals were irrigated with various solutions: 11.5% polyacrylic acid for 30 s, 17% EDTA for 60 s, or 5% NaOCl for 60 s, respectively. Irrigation with distilled water was used in the control group. After all specimens had been rinsed with distilled water, the excess moisture was removed and the posts were luted using either BisCem (Bisco) or RelyX Unicem clicker (3M ESPE). Seven days after luting, the specimens were sectioned transversally into 1-mm-thick slices, which were submitted to push-out testing on a mechanical testing machine. Bond strength data (n = 6 per group) were analyzed by two-way ANOVA and Student-Newman-Keuls' test (α = 0.05). For Unicem, EDTA showed lower bond strength than the other solutions, which had similar results. For BisCem, EDTA showed higher bond strength than the other treatments, while application of NaOCl yielded higher bond strength than polyacrylic acid whereas the control group had intermediate results. In conclusion, irrigating root canals before insertion of self-adhesive resin cements, especially EDTA, might interfere with retention of the fiber posts.

A 12-month clinical evaluation of pit-and-fissure sealants placed with and without etch-and-rinse and self-etch adhesive systems in newly-erupted teeth

OBJECTIVES: The objective of this one-year clinical study was to investigate the effect of two adhesive systems (Adper Single Bond, a two-step etch-and-rinse and Clearfil SE Bond, a two-step self-etch system) on pit-and-fissure sealant retention in newly-erupted teeth. This study compared the success of the sealants in mesial and distopalatal grooves with and without these two adhesive systems. MATERIAL AND METHODS: In a clinical trial, 35 children aged 6-8 years undergoing sealant placement were recruited. This one-year clinical study scored 70 mesial and 70 distopalatal sealants of newly-erupted permanent maxillary first molar, with a split-mouth design. All children received sealant alone in one permanent maxillary molar tooth. Children were randomized into two groups. One group received Self-etch (Se) bond plus sealant and the other group received Single Bond plus sealant in another permanent maxillary molar tooth. Clinical evaluation at 3, 6 and 12 months was performed and the retention was studied in terms of the success and failure. RESULTS: The success rate of sealant in the distopalatal groove, using SeB at 3, 6 and 12 months was 93.3% (95% CI: 68.0, 99.8), 73.3% (95% CI: 44.9, 92.2) and 66.7% (95% CI: 38.4, 88.2), respectively. It was greater than that of the distopalatal groove in SB group with a success rate of 62.5% (95% CI: 35.4, 84.8), 31.3% (95% CI: 11.8, 58.7) and 31.3% (95% CI: 11.8, 58.7), at the three evaluation periods. The success rate of sealant in the mesial groove using SeB was 86.6% (95% CI: 59.5, 98.3), 53.3% (95% CI: 26.6, 78.7) and 53.3% (95% CI: 26.6, 78.7), while this was 100% (95% CI: 79.4, 100.0), 81.3% (95% CI: 54.4, 96.0) and 81.3% (95% CI: 54.4, 96.0) using SB, at 3, 6 and 12-month evaluation periods. CONCLUSIONS: These results support the use of these two bonding agents in pit-and-fissure sealants under both isolated and contaminated conditions. Further, Se bond seemed to be less sensitive to moisture contamination.

Two-year clinical evaluation of three adhesive systems in non-carious cervical lesions

OBJECTIVES: Adhesive systems are continuously being introduced to Dentistry, unfortunately often without sufficient clinical validation. The aim of this study was to evaluate the clinical performance of cervical restorations done with three different adhesive systems. MATERIAL AND METHODS: 158 non-carious cervical lesions of 23 patients were restored with a nanofilled composite resin (Filtek Supreme, 3M/ESPE) combined with Single Bond (3M/ESPE, group SI), Clearfil SE (Kuraray Medical Inc., group CL) and Xeno III (De Trey Dentsply, group XE). In groups SI-B, CL-B and XE-B, the outer surface of the sclerotic dentin was removed by roughening with a diamond bur before application of the respective adhesive systems. In groups CL-BP and XE-BP, after removal of the outer surface of the sclerotic dentin with the bur, the remaining dentin was etched with 37% phosphoric acid and the self-etch adhesive systems Clearfil SE and Xeno III were applied, respectively. Lesions were evaluated at baseline, and restorations after 3 months, 1 year and 2 years using modified USPHS criteria. RESULTS: After 2 years, no significant difference was found between the retention rates of the groups (p >0.05). Although groups CL and SI showed significantly better marginal adaptation than group XE (p<0.05) at 2 years, no significant difference was found between the marginal adaptation of the groups SI-B, CL-B and XE-B (p>0.05). After 2 years no significant difference was observed among the marginal staining results of all groups (p>0.05). CONCLUSION: Although all adhesive systems showed similar retention rates, Clearfil SE and Single Bond showed better marginal adaptation than Xeno III after 2 years of follow-up.

Efecto del grabado de la dentina radicular con ácido dietilenoaminotetra acético (EDTA) en la resistencia de unión de cementos autoadhesivos y autograbantes / Effect of engraving dietilenoaminotetra acetic acid (EDTA) root dentin in the resistance of cemented joints stickers and etching

Fue evaluado el efecto del grabado de la dentina radicular con EDTA en la resistencia de unión (RU) inmediata (IM) y después de termociclaje (TM) de un cemento autoadhesivo (AA) y uno auto grabador (AG) para la cementación de postes de fibra de vidrio. Fueron utilizadas 40 raíces de premolares humanos divididas en 4 grupos según tipo de cementación (n=10) G1 RelyX U100 (UC) según indicaciones del fabricante(IF); G2 grabado con EDTA 24% por 60 s antes de la aplicación del UC ; G3 Para Post Para Core Automix (PC) (IF)G4 - grabado con EDTA 24% por 60 s antes de la aplicación del (PC).Las raíces fueron cortadas en discos de 1 mm (dos discos por tercio radicular), la mitad de los discos fueron sometidos a ensayo expulsión IM (0,5mm/min) y la otra mitad después de TM (5º C e 55º C).los datos fueron analizados en test de ANOVA y Tukey (?=0,05).dando como resultado que el grabado con EDTA altero negativamente los valores de RU solo del tercio cervical en los dos cementos. Cuando fue comparado TM con IM con o sin aplicación de EDTA no se encontraron diferencias estadísticas significativas. Para todos los grupos testados.El cemento PC obtuvo mayores valores de RU (19,59 MPa) comparado con el UC (15,80 MPa).concluyéndose que el tratamiento con EDTA afecto la RU solo para el tercio cervical tanto en IM como TM en los dos cementos. El TM con o sin EDTA no afecto los valores de RU cuando comparado con IM

The effect of post-space treatment whit EDTA on the bond strength (BS) of fiber posts in different root regions was evaluated using two different type of resin cements Rely X U100 (UC) and Para Post Para Core automix (PC) . Fourty extracted premolars root canals were assigned to four groups of 10 roots each. G1 RelyX U100 (UC) according to manufacturer's instructions (MI), G2 etching whit EDTA 24% for 60 s before application of UC; G3 Para Post Para Core Automix (PC) MI; G4 Etching whit EDTA 24% for 60s before application off PC. After cementation the roots were sectioned in 6 slices 1mm each (two slides for root region) and randomly divided into two subgroups, depending on testing time immediate (IM) vs. after termocicling(TM) ), for expulsion test. Statistical analysis was performed with ANOVA and Tukey test (?=.05) No differences in BS was found among the groups whit and whit out EDTA 24 %. Etching whit EDTA adversely alter the BS values of the cervical third in the two cements. When TM was compared with IM with or without application of EDTA there was no statistically significant difference. For all groups tested, PC show higher values of BS (19.59 MPa) was compared with UC (15.80 MPa). Concluded that treatment with EDTA affected the BS only on the cervical third in both IM and TM in the two cements. The TM with or without EDTA did not affect the values of BS when compared with IM

Glass ionomer cement as an occlusive barrier in Class III furcation defect.

Predicting the prognosis of molars that have experienced furcation invasion, is often a frustrating experience to the dental clinician and disappointing report to the patient involved. Although multiple treatment modalities have been attempted to retain teeth with severe furcation invasion, clinical success has not been predictable. A case report involving the use of glass ionomer cement (GIC) as an occlusive barrier in the management of Class III furcation defect involving mandibular first molar is presented. A literature review on the subject matter was conducted using Medline, Google search engines, and manual library search. GIC restoration of Class III furcation invasion gives a satisfactory result. Surgical and nonsurgical treatment options are available for the management of the condition. GIC as an occlusive barrier in Class III furcation invasion is an economical and less invasive treatment option. It also makes home care easy for the patient.

Análise da força de tração necessária para a remoção de cimento resinoso fixado em raízes preparadas com diferentes substâncias químicas / Analysis of the force required to remove resin cement from roots prepared with different chemicals

OBJETIVO: Avaliar in vitro, a influência das substâncias químicas utilizadas durante o preparo endodôntico na força de tração do cimento resinoso Rely-X (3M, Sumaré, Brasil) na dentina radicular bovina. MÉTODOS: Utilizou-se 72 dentes bovinos que tiveram suas coroas seccionadas e raízes padronizadas. A seguir, os espécimes foram incluídos em blocos de resina e receberam tratamento químico por 10 minutos com hipoclorito de sódio nas concentrações de 0,5 por cento, 1 por cento, 2,5 por cento, 5,25 por cento ou gel de clorexidina a 2 por cento, além do grupo-controle que recebeu água destilada. Em seguida os espécimes foram imersos em solução de EDTA a 17 por cento por 3 minutos. Dois espécimes de cada grupo foram submetidos à microscopia eletrônica de varredura para avaliação da superfície. Os espécimes para o ensaio de teste de tração receberam condicionamento com ácido fosfórico a 37 por cento por 15 segundos, sistema adesivo Single-Bond (3M, Sumaré, Brasil) e sobre este aplicado o cimento resinoso Rely-X (3M, Sumaré, Brasil). RESULTADOS: Os resultados em Kgf foram: GClorex (2,26); GNaOCl-0,5 por cento (7,92); GNaOCl-1 por cento (9,70); GNaOCl-2,5 por cento (9,05); GNaOCl-5,25 por cento (8,91); GA (0,61). CONCLUSÃO: O hipoclorito de sódio nas concentrações testadas aumentou a força de adesão do cimento resinoso na dentina de forma significativa frente água destilada e gel de clorexidina a 2 por cento. A observação na microscopia eletrônica de varredura mostrou que a estrutura de dentina radicular que fora tratada com hipoclorito de sódio apresentava túbulos dentinários com diâmetros aumentados, menor quantidade de dentina intertubular, além de áreas de depressões, diferentemente dos grupos-controle e gel de clorexidina a 2 por cento.

OBJECTIVE: This study assessed in vitro how the chemicals used in the preparation of root canals affected the force required to remove the resin cement Rely-X (3M, Sumaré, Brazil) from bovine root dentin. METHODS: The crowns of 72 bovine teeth were sectioned and the roots were standardized. The specimens were then placed in resin blocks and treated for 10 minutes with sodium hypochlorite at 0.5 percent, 1 percent, 2.5 percent or 5.25 percent or chlorhexidine gel at 2 percent. The control group was treated with distilled water. Next, the specimens were soaked in 17 percent EDTA for 3 minutes. The surfaces of two specimens from each group were assessed by electron scanning microscopy. The tested specimens were then treated with 37 percent phosphoric acid for 15 minutes, adhesive system Single-Bond (3M, Sumaré, Brazil) and the resin cement Rely-X (3M, Sumaré, Brazil) was applied over it. RESULTS: The results in Kgf were: GChlorhex (2.26); GNaOCl-0.5 percent (7.92); GNaOCl-1 percent (9.70); GNaOCl-2.5 percent (9.05); GNaOCl-5.25 percent (8.91); GA (0.61). CONCLUSION: Sodium hypochlorite in the tested concentrations increased the adhesion of the resin cement to the dentin significantly when compared with water and 2 percent chlorhexidine. Electron scanning microscopy showed that the structure of the root dentin treated with sodium hypochlorite presented widened dentinal tubules, less intertubular dentin and depression areas, all of which were not observed in the roots treated with water and 2 percent chlorhexidine gel.

Restauração com pinos intrarradiculares anatômicos em grandes destruições coronárias / Restoration with intraradicular anatomical posts in flared root canals

o tratamento endodôntico em dentes com grande destruição coronária é um procedimento clínico comum no cotidiano das clínicas odontológicas. Na maioria destas situações clínicas, há a indicação do uso de retentor intrarradicular para dar estabilidade e retenção à restauração. Uma das técnicas propostas para o tratamento de canais amplos é a utilização de um pino de fibra de vidro com módulo de elasticidade próximo ao da dentina, remodelado com resina composta para preencher o espaço existente no canal radicular alargado. Esta técnica reduz quantidades excessivas de cimento que serviriam para substituir a estrutura dental perdida e permite uma boa adaptação no conduto radicular, criando condições favoráveis para retenção do pino. O objetivo deste trabalho foi demonstrar a técnica de anatomização de pinos intrarradiculares estéticos com resina composta, em incisivo anterior com grande destruição coronária. A utilização de um pino de fibra de vidro anatômico foi a alternativa indicada para a resolução clínica de forma a proteger o remanescente dental enfraquecido, além de obter estética aliada a um prognóstico favorável.

Root canal therapy in teeth with large coronal destruction is a common clinical precedure in the daily dental clinics. In most of these conditions, there is an indication of the use of intra-radicular post for stability and retention for the restoration. One of the techniques proposed for the treatment of enlarged channels, is the use of a fiber glass with modulus of elasticity similar to dentin, restored with composite resin to fill the space between the root canal extended. This technique reduces excessive amounts of cement that would serve to replace the lost tooth structure and allows a good adaptation in the root canal, creating favorable conditions for retention of the post. The objective was to demonstrate the technique of anatomization intraradicular aesthetic post with composite resin in anterior incisor with large coronal destruction. The use of a fiber glass anatomical was the alternative used for clinical resolution in order to reinforce the remaining tooth structure weakened, returning him to function without requiring the removal of sound tooth structure, and aesthetics combined with a more favorable prognosis.

Evaluation of demineralization adjacent to orthodontic bracket and bond strength using fluoride-releasing and conventional bonding agents.

Background and Objectives: One of the most difficult problems encountered in orthodontic treatment with fixed appliance is the control of enamel demineralization around the brackets. Fluoride-releasing bonding adhesives were introduced to aid in the prevention of demineralization adjacent to orthodontic brackets. Hence, an in vitro study was conducted to evaluate and compare demineralization adjacent to the orthodontic bracket and the bond strength using fluoride-releasing adhesive and conventional adhesive. Materials and Methods: One hundred and twenty healthy extracted premolars were selected for the study and were divided into two groups, each group consisting of 60 teeth. Both groups were further divided into three subgroups consisting of 20 samples each. Samples of subgroups A and B were bonded with two prototypes of fluoride-releasing adhesives (i.e. Rely-a-bond and Tru-bond). Samples of subgroup C (ortho-one) were bonded with conventional non-fluoride-releasing adhesive. Group I samples were subjected to demineralization in an acidic medium (methyl cellulose buffered with acetic acid at a pH of 4.5) for 4 weeks, which were later observed under a stereomicroscope. Group II samples were tested for shear bond strength using the Instron Universal testing machine. Results: Both fluoride-releasing adhesives showed statistically significant lower enamel demineralization around the bracket when compared with the conventional adhesive. There was no statistically significant difference on comparing the demineralization between the two prototypes of fluoride-releasing adhesive. Evaluation of shear bond strength revealed that there was no significant difference between the subgroups. Conclusion: Fluoride-releasing adhesives might aid in the prevention of demineralization adjacent to the orthodontic bracket with acceptable bond strength.

Comparative efficacy of two treatment modalities for dentinal hypersensitivity: A clinical trial.

Background: Dentin hypersensitivity is a recurrent condition causing discomfort and sometimes pain to the patient, which also deters him from maintaining adequate oral hygiene. Home care and office measures are used for treatment of this malady. Aim: To evaluate and compare the efficacy of 2 treatment modalities for dentinal hypersensitivity, iontophoresis with acidulated phosphate gel (APF) gel, and dentin-bonding agent application. Materials and Methods: This split mouth randomized clinical study recruited subjects with a history of hypersensitivity with at least 2 teeth, verified by a light stroke with a dental explorer along the cervical third of the teeth. The patients were subjected to a 1-s air blast and cold water stimuli and their responses were recorded on a verbal rating scale. A total of 30 sites from 15 patients were divided into Group A-1.23% APF gel iontophoresis; and Group B-aqueous solution of hydroxyl-ethyl-methacrylate and glutaraldehyde. The teeth were evaluated immediately after the treatment and at the end of 2 weeks. In case of failure, the tooth was retreated with the same agent as before. Results: The results were statistically analyzed using Kruskal-Wallis analysis of variance and Mann-Whitney U tests. There was no statistically significant difference between the groups at the end of 2 weeks. However, Group A was more effective clinically, with fewer number of failures compared with Group B. Conclusion: Both the agents showed a statistically significant reduction in sensitivity compared with baseline; however, APF gel iontophoresis was more effective in reducing hypersensitivity over a longer time period.